During highly dynamic parts of an audio track (e.g. tutti fortissimo of a full symphonic orchestra, sounds of large ethnic drums, bass parts of experimental electronic music, cinematic SFX) a powerful amplifier must draw substantial current surges from a power supply unit, which can reach magnitudes of 50–100 A, while maintaining voltage levels without dips. An ordinary domestic socket, which is connected to a distribution board using long electrical cables, is not capable of providing such current levels due to relatively high output impedance. ST-5000 has an output DC resistance of 0.4 Ω therefore it can easily supply high current surges without facing voltage dips. This is achieved by using a transformer with a very large core resulting in a very small magnetic flux density. In turn the response time of a power amplifier to a changing audio signal is reduced, which benefits reproduction of transients, especially in lower frequency bands. An audio reproduction system exhibits a wider dynamic range, which results in more realistically sounding musical instruments and cinematic SFX.
Another problem in power supply of high-quality equipment is noises in electrical networks. They appear when switches and controllers of electrical motors, dimmers and regular lighting, as well as switch-mode power supply units of modern AV equipment are used nearby. High-quality CEE 7/3 sockets are galvanically isolated from an external electrical network. The transformer is equipped with a reliable electrostatic shield. Arriving electrical interferences are counteracted using a mutual cancellation principle. The secondary winding of the transformer is separated into two halves and has an artificial centre tap, which is connected to the earth clips of each socket outlet. The ST-5000 transformer was designed to work as low-pass filters with a cut-off at 800 Hz, since all electrical network interferences happen at much higher frequencies. Secondly, the filtering effect is caused by self-inductance of a very large core, because of which magnetic flux cannot change instantaneously under a transient disturbance. All of the above technical aspects allow to almost entirely remove electrical network noises providing reliable high-quality power supply to audio equipment.
When the power conditioner is first switched on the transformer is subject to an inrush current of approximately 20 A during magnetisation of the transformer core. Due to this a soft start is implemented into the power conditioner. A special ballast resistor limits the current surge, so that other electrical equipment, which is connected to the same electrical network, remains unaffected.
Audes power conditioners have an overload protection and a thermal protection, which switches the transformer off if temperature of the transformer reaches 90 °C. Once the temperature drops to 75 °C the device will reconnect to the electrical network automatically. The transformer was designed to maximise the number of turns in the primary winding. Because of this under the no-load condition the power consumption of ST-5000 is only 16 W.
The normal operating ambient temperature range for ST-5000 is 10–25 °C. At lower temperatures additional heating is required to prevent condensation. At higher temperatures additional external cooling is required.
ST-5000 produces virtually no acoustic noise, which allows its use not only with domestic High-End audio equipment, home cinemas and show rooms, but also in sound recording studios.
Power rating: 5000 V∙A
Inlet: powerCON 32 A connector Neutrik NAC3MP
Outlet:16 A/250 VAC Socket CEE 7/3 (× 9)
Power Supply Cable: powerCON 32 A/250 VAC cable connector Neutrik NAC3FC (Power сable not included)
Dimensions (mm): 260 H × 435 W × 347 D
Dimensions (inches):10¼” H × 17⅛”* W × 7¾” D
Weight: 45 kg / 100lbs
- Scott's white paper here
- The Ear GC-1 review here
- The Ear GC-3 review here
- HiFi+ review here
- Stereotimes GC-1 review here
- The Audio Beat GC-1 & GC-3 review here
- The Audiohileman's GC-1 & GC-3 review
- GC1 includes 1 cable
- GC3 includes 2 cables
- If you are outside the UK please contact MCRU before purchasing any CAD product
Balanced mains power for lower noise floor, more detailed and natural sounding audio and A/V quality.The AC-2K Balanced unit from connected-fidelity™ is not just another form of mains power cleaning or ‘noise control’ treatment. It is a fundamentally different approach.
- Remove mains noise from your system
- USA version only no others available
- Special edition
- 1 unit in BLACK with full warranty
- Suitable for all audio or AV systems
- RFI reduction 75dB
- 6 optimised power cleaning circuits Removes Common and Differential Mode mains noise
- 4 independent outlets for source components (10A max each)
- 2 independent high current outlets for power amps, subwoofers, active speakers etc.. (16A max each)
- 108,000A instantaneous protection
- Fully star-earthed network
- Solid core Ohno Continuous Cast copper silver-plated internal wiring with FEP virtual air dielectric.
- Supplied with IsoTek’s award winning EVO3 PREMIER POWER CABLE
- UK, EU, US, AU & CH outlets available
- Supplied with IsoTek power EVO3 Premier power cord as standard
- Compact yet elegant design
- Suitable for all audio or AV components, but dedicated for high current use, power amplifiers, subwoofers, active loudspeakers
- ONE UNIT EX-DEM MINT CONDITION WITH FULL WARRANTY - BLACK
- NO OTHER OFFERS APPLY OR CAN BE USED
- FREE MCRU 4 WAY EXTENSION HUB TO ATTACH TO THE TITAN